mrsrefa.blogg.se - American standard toilet overflow tube

AMERICAN STANDARD TOILET OVERFLOW TUBE FULL
AMERICAN STANDARD TOILET OVERFLOW TUBE DOWNLOAD
AMERICAN STANDARD TOILET OVERFLOW TUBE FREE
AMERICAN STANDARD TOILET OVERFLOW TUBE WINDOWS

AMERICAN STANDARD TOILET OVERFLOW TUBE DOWNLOAD

Or Download the Duo Flush System Toilet Converter installation instructions Replace the tank lever without the spacer and retry the flush.Snap actuator box onto tank lever thread.Tighten lock nut onto the tank lever thread this is a reverse threaded nut, turn nut clock wise to tighten nut.Make sure to push the lever all the way in ensuring the tank lever is flush with the face of the tank. Replace tank lever back into the tank’s lever mounting hole.Remove the black rubber (square shaped) spacer from tank lever’s spacing nut.Remove the toilet handle from the front of the tank.Remove the lock nut from toilet handle thread this is a reverse threaded nut, turn nut counterclockwise to release the nut.Push the button on the top of the actuator handle box and release the box and cable from the tank lever thread.Remove the toilet lever from the tank and remove the black spacer from the tank lever spacing nut, follow these steps: The tank lever sticks in the up or down position, it does not return to a horizontal position after you flush. Simply push in the button and pull away from the tank lever.Ħ. On newer versions on the Duo Flush, there is a push button on top of the activation box.You may need to give it a strong jerk to unsnap it. On older versions of Duo Flush, grab hold of the activation box in the tank and pull it toward the back of the tank.Removing the activation box (both newer and older versions of the converter) once it has been snapped onto to the tank lever. Gently rock the Duo Flush canister away from the overflow pipe and pull up.ĥ.Removing the Duo Flush valve from the seat Replace Duo Flush onto valve seat and turn on water, check for leaks.Ĥ.Make sure the refill tube (rubber hose) is clipped to the side of the overflow pipe and not directly shoved into the overflow pipe.Inspect the overflow pipe for obvious cracks.

If seal is good reseat angled seat adaptor. If you get black residue on your fingers when you touch the seal, replace the flush valve.

Check the black seal at the base of your original flush valve/ overflow pipe unit.

Turn adapter upside down and reshape putty ring, spread putty evenly around entire base of adaptor.

AMERICAN STANDARD TOILET OVERFLOW TUBE FREE

Pull angled seat adapter straight up until it pulls free from flush valve seat.

Remove the Duo Flush valve from the valve seat and clean both the Duo Flush seal and the plastic seat the seal sits upon.

Water is leaking from the tank into the bowl at one or more leak points. Fill valve turns on and off periodically (ghost flushing). Fluidmaster recommends using the 400AH PerforMAX Fill Valve.ģ.

If you are not using Fluidmaster’s PerforMAX fill valve, your fill valve may not have enough output to refill the bowl.Repeat this process until the proper water level is reached.Using the GREEN dial, adjust the half flush setting one setting higher.

AMERICAN STANDARD TOILET OVERFLOW TUBE FULL

The “Rolling Pin” should be set to “8” which is full flow.

Adjust the roller clamp on the refill tube so that it is allowing full flow.

Make sure the refill tube (rubber hose) is supplying water down the overflow pipe and not into the tank.

Make sure the water level in the toilet bowl is up to its highest capacity.

Water level is half way or completely over the oval opening and the full and half flush are working but the bowl is not clearing out.

Set the BLUE dial one to two settings higher than that of the GREEN dial.Ģ.

This is the lowest possible setting while maintaining a good half flush.

Continue this process until toilet does not evacuate the paper and adjust dial up 1 setting.

Place 3 pieces of toilet paper in the bowl and flush, if the bowl evacuates the toilet paper, lower the green dial setting by one number and repeat flush.

Once water level has been set, set both adjustment dials to maximum setting.

If your water level cannot be increased, the Duo Flush system should not be used.

AMERICAN STANDARD TOILET OVERFLOW TUBE WINDOWS

Set water level higher: Water level should be half way to all the way over the oval windows of the Duo Flush valve (See picture below).The Full and / or Half flush closes immediately after tank lever is released.